Display Controller booting into BIOS or Windows recover

Display Controller (DC) – Boot Issues & Troubleshooting Guide

Overview

If your bowling lane Display Controller (DC) fails to start correctly, it may boot into BIOS, Windows Recovery, or become stuck in a continuous reboot loop.

When this happens, the controller is not running Windows normally, meaning Bowling Vision Support cannot remotely connect to the controller.

Therefore, someone on-site will need to physically access the Display Controller to perform the troubleshooting steps.


Below is a diagram on troubleshooting the issue, with steps explained below in further detail:

Step 1 – Physically Restart the Display Controller

The first step is to perform a normal restart using the physical power button on the controller.

For instructions on locating the Display Controller and safely restarting it, please refer to our existing Display Controller Reboot Guide, available on the Bowling Vision Knowledgebase.

https://support.bowlingvision.com/article/390-manually-rebooting-a-display-controller


Once restarted, allow the controller time to boot and check whether the bowling lane displays return to normal.

If the controller continues to boot into BIOS, Windows Recovery or a reboot loop, proceed to Step 2.

Step 2 – Perform a Hard Restart

  1. Locate the physical power button on the Display Controller.
  2. Press and hold the power button for approximately 10–15 seconds until the controller powers off completely.
  3. Wait a few seconds.
  4. Press the power button again to switch the controller back on.
  5. Check whether Windows starts normally.

If the issue continues, proceed to Step 3.

Step 3 – Perform a Full Power Cycle

  1. Switch off the Display Controller.
  2. Carefully disconnect its external power cable.
  3. Leave the controller disconnected for approximately 5 minutes.
  4. Reconnect the power cable securely.
  5. Switch the controller back on and check whether it starts normally.

Only disconnect the external power connection. Do not open the controller or disconnect internal components.

Step 4 – BIOS or Windows Recovery Troubleshooting

If the controller still fails to start, connect a USB keyboard and mouse directly to the Display Controller.

If the Controller Boots into BIOS

  1. Using the keyboard, locate the Exit menu.
  2. Select Exit Without Saving or Discard Changes and Exit, if available.
  3. Confirm the selection and allow the controller to restart.
  4. Check whether Windows loads normally.

If the controller returns to BIOS, please contact Bowling Vision Support.

Do not modify BIOS settings or restore defaults unless instructed by our technical support team.

If the Controller Boots into Windows Recovery

  1. Select Continue – Exit and continue to Windows, if available.
  2. If the controller returns to Windows Recovery, select Troubleshoot → Advanced options → Startup Repair, if available.
  3. Follow the on-screen instructions and allow the repair process to finish.
  4. Check whether Windows starts normally.

Do not select Reset this PC, reinstall Windows or format any drives.


Step 5 – Replace the Display Controller with a Spare (If Available)

If the Display Controller continues to fail after completing the troubleshooting steps above, and your venue has a working spare Display Controller available, you may be able to replace the faulty unit to restore normal operation.

Before proceeding, ensure the replacement Display Controller is compatible with your bowling system and configured correctly.

For instructions on safely removing the faulty Display Controller and installing the replacement, please refer to our Display Controller Replacement Guide, available on the Bowling Vision Knowledgebase.

https://support.bowlingvision.com/article/428-replacing-a-display-controller


Once the replacement has been installed:

  1. Power on the replacement Display Controller.
  2. Allow the controller to boot into Windows.
  3. Check that the affected bowling lane displays are functioning correctly.
  4. Confirm that the lanes are operating normally.

If the replacement Display Controller is working correctly, no further troubleshooting of the installed unit should be required.

Important: Please notify Bowling Vision Support of the replacement by sending us the serial number of both units so we can record the faulty unit and advise on any further action required.

If a working spare is unavailable, or the replacement does not resolve the issue, please proceed to Step 6 and contact Bowling Vision Support.


Step 6 – Contact or refer back to Bowling Vision Support

If the Display Controller continues to boot into BIOS, Windows Recovery or a reboot loop after following these steps, please contact our support team.

Email: support@bowlingvision.com

Whatsapp number: +44 7586 832088 (Message only)

Support number: +44 03301220252


Please include:

  • Your venue name and affected lane numbers.
  • Photographs of the BIOS, Windows Recovery or error screen.
  • A short video showing what happens when the controller starts.
  • A brief description of the troubleshooting steps already attempted.

As remote access is unavailable while the controller is unable to boot into Windows, this information will help our technical support team investigate the issue and advise on the next steps.