Replacing a Display Controller

Procedure

Uninstalling a Display Controller

AAEON Sync Display Controller installed


Tools Needed

  • Phillips Head Screwdriver (M5)

  1. Power off the Display Controller.

    Note any connected/plugged in cables on the current Display Controller, then unplug each of the following:

    1. Power Cable
    2. HDMI Cable(s)
    3. Ethernet Cable
    4. Serial Cable(s) (if applicable)

      If the Display Controller is installed with specific Samsung BEC, BED, BET or BEH model televisions, the serial ports (COM1, COM2) are not used. For other supported overhead monitors, serial cables should be connected to each overhead monitor from the COM1 and COM2 ports of the display controller.

  2. Twist the knob that locks the Display Controller to the clamp and the overhead truss.
  3. Remove the Display Controller (and the attached hanging straps) from the overhead truss.

These diagrams are excerpted from the Sync installation manual for the Industrial PC v2 and Industrial PC v3 model display controllers for general reference only.


Industrial PC v2 - Sync Display Controller

SyncInstallationManual_Fig04-17_IPCv2.png


Industrial PC v3 - Sync Display Controller

SyncInstallationManual_Fig04-16_IPCv3.png



Replacing a Display Controller


Tools Needed

  • Phillips Head Screwdriver (M5)

  1. Install the provided adapter brackets to the display controller, then use the provided screws to secure the brackets to the unit.
  2. Mount the display controller to the hanging strap, then secure the display controller using the provided screws.
  3. Install the display controller in the same location as the previously removed hardware.
  4. Use the knob to secure the display controller and attached hanging strap to the overhead truss.
  5. Connect the following cables to the Display Controller:
    1. Serial Cable(s) (if applicable)
    2. Ethernet Cable
    3. HDMI Cable(s)
    4. Power Cable
  6. If necessary, press the power button on the Display Controller to turn the unit on.
  7. If necessary, power on any connected overhead monitors for the lane / lane pair.


Configuring the Display Controller

Once the Display Controller has powered on and Sync has started, the overhead monitor should display a message:

  • Please configure this device
  • Please reconfigure this device

Make a note of the IP address on the monitor (typically 192.168.90.x) and follow the directions below.


Caution

The provided steps should be correct for a new, previously unconfigured display controller. If you are unable to follow the provided directions - contact Bowling Vision Support for assistance.


  1. Open 

     Sync Office and log in.

  2. Navigate to Admin > System Control.

    2025-04-08_16-50-21.png

  3. In the list of Sync devices, click on the display controller that was replaced (ex. DC1-2 would be Lanes 1-2).
  4. In the IP Address textbox, key in the IP address noted on the overhead monitor, then click Configure.

    The Display Controller should indicate it is rebooting and then restart.

    2025-04-08_16-54-55.png

After the display controller reboots, it will download and install any necessary updates or content. 

The progress of this update can be seen on the overhead monitor and/or in Sync Desk.



Testing the Lane / Lane Pair

Once the Display Controller has been configured and updated, the lane / lane pair should be ready to use in Sync Desk.

  1. Open 

    Sync Desk icon

     Sync Desk and log in.

  2. Issue a Lite League or game to the lane / lane pair.
  3. At the bowler console, select a game and enter a name (as needed) at each lane.
  4. Both lanes should start up and the game should start.
  5. Verify the lane starts, scores, cycles and resets as normal.

Troubleshooting


The "Please configure" or "Please reconfigure..." Message Does Not Display on the Overhead Monitors.

This typically occurs if the Display Controller was previously configured for use with Sync. Please contact Brunswick Technical Support (BTS) for assistance.


The Overhead Monitor Displays a "Sync Network Not Available" Message

This issue typically occurs if the Display Controller is not connected to the Sync Network. It is recommended to contact Brunswick Technical Support (BTS) for assistance.


The Bowler Console or Pinsetter Does Not Respond to a Game Being Issued.

This issue typically occurs if there is a synchronization issue between the lane tablet, display controller and pinsetter controller.

  1. Open 

    Sync Desk icon

     Sync Desk and log in.

  2. Turn off any issued game(s) to the lane / lane pair.
  3. Click the lane / lane pair.
  4. Click More > Device Control.
  5. Click the toggle for Display Controller, Tablet, Distribution Board (Pinsetter) and Spark as available.
  6. Click Reboot.

Once the lane devices have completed rebooting, try re-issuing the lane pair.

If the issue continues, please contact Brunswick Technical Support (BTS) for assistance.


Commercials / Scoresheets Do Not Display Correctly OR Scoresheets Are Displayed on the Wrong Monitor

If the commercials or scoresheets do not use the full-screen of the monitor or scoresheets are displayed on the wrong monitor, then please do the follow these steps:

  1. Open 

    Sync Desk icon

     Sync Desk and log in.

  2. Click the lane / lane pair.
  3. Click More > Monitor Control.

Commercials / Scoresheets are the Wrong Size:

  1. Click Fix Displays.

Scoresheets are Displayed on the Wrong Monitor

  1. Click Swap Displays.
  2. Verify the scoresheets are now on the correct overhead monitor.